Starting Gas Fireplace Pilot Light

Resetting IPI Plus System. Hold the gas control button down while you hold the end of a lighted match or lighter at the end of the pilot tube.

How To Light Your Pilot Light On A Gas Fireplace Heatilator

If you do this correctly the pilot light should start as soon as the flame is close enough.

Starting gas fireplace pilot light. Use Care Videos. Because that system does not use external electricity the fireplace works if the power goes out. Step 3 - Locate the Spark Ignitor.

The pilot must generate enough Millivolts of electricity to open and close the gas valve. Gas Fireplace Pilot Light On But Wont Start. You need to understand that most Gas Fireplaces have pilots which use about 900-1100 BTUhr.

Gas fireplaces have traditionally used a standing pilot light to ignite the flames. Direct Vent Gas Fireplace. Model.

Light the Pilot Light The next very important step in how to light a gas fireplace is to light the pilot light. Next locate the pilot assemblys spark ignitor. The valve can get turned off and forgotten about quite easily.

Repeat this step as necessary until the pilot ignites. You can do this by turning the knob to the Pilot position. By On Apr 19 2021.

Hold the pilot button down for about 20 seconds to give the thermocouple time to. This makes the fireplace easy to start when its cold outside but when it warms up its a good idea to shut off the pilot to conserve gas. Keep in mind that most gas fireplace models will have a manual switch present.

It should resemble something like a. Replacement piezo ignitor httpamznto2i7clAn Replacement Thermopile httpamznto2j1sFm3WARNING. This continuous flame is necessary to light large burners such as those found in gas fireplaces.

If the on switch is left on for more than 60 seconds and the pilot does not light the fireplace will go into lock out mode. Install. You would be surprised at just how often this is the culprit for a gas fireplace failing to start.

If yours appears to be the mirror image of picture 4 then the word PILOT will be in the 12 oclock position to light the pilot and ON will be set to the 12 oclock position to turn on your main burner. Find the valve on the gas supply line and turn the. Press and continue to press down on the control knob while UD press the ignition switch one time per second.

Most gas fireplaces have a standing pilot light which is a small flame that burns even when you arent using the fireplace. When the fireplace or propane heater is turned on the pilot light serves as an ignition source for the larger sweep of gas released from the burner. That switch must be engaged for the gas fireplace to light.

ALWAYS REMOVE YOUR FIREPLACE GLASS PRIOR TO LIGHTING YOUR PILOT. Light the flame with a match or long-barreled lighter. Keep trying periodically to light the pilot light.

The pilot light flame must hit the thermocouple correctly or the voltage the thermocouple generates may not be enough to operate the main gas valve while it is enough to keep the pilot light lit. A pilot light is a small flame that is kept alight using a steady small stream of gas. This is pretty powerful and for good reason.

This also means that it uses a fair amount of gas. The first thing that you should do is to check the main gas valve. The controls should be set to the Off position before starting a gas fireplace indicated here to be in the 12 oclock position for our fireplace We simply needed to depress the dial and turn it clockwise until its at the 12 oclock position before attempting to light the fireplace.

If the pilot does not light within 45 seconds turn the onoff switch back to the off position and wait 15 seconds. Intermittent Pilot Ignition IPI mode means that the pilot light will light and extinguish each time the unit is used the ignition system will first ignite the pilot light before opening the gas valve to the main burner and igniting the fireplace. This process may take several minutes and several attempts.

A benefit of IPI mode is that it is more cost effective efficient and environmentally friendly. The pilot light flame must hit the thermocouple correctly or the voltage the thermocouple generates may not be enough to operate the main gas valve while it is enough to keep the. Locate the Gas Supply Line.

This allows the gas to reach the pilot assembly. The pilot light systems are actually the most common reason that gas fireplaces do not light however. Newer generations of gas fireplaces use an electronic ignition system requiring electricity to start up.

Steps To Light Your Gas Fireplace Step 2 - Locate the Gas Supply Line. Gas fireplaces are very safe when used properly. Choose white and you will possess an impeccable fireplace completing as its unique and refined.

Read and follow the instructions that came with you.

How To Light Your Pilot In A Napoleon Gas Fireplace Youtube